Your laptop screen is on, but the pointer is frozen or gone entirely, making it impossible to click anything. This page gives you the exact steps to test if the mouse sensor, touchpad, or its connection is physically broken.
In short: If your cursor is stuck, the problem is usually a disconnected ribbon cable, a failing optical sensor, or a loose battery clip pressing on the touchpad logic. Start by moving a USB mouse to rule out the touchpad, then check for loose internal screws or cables that shift when you open the laptop lid.
Our pick
Tap to see today's price on AmazonA wired USB mouse bypasses internal touchpad hardware to confirm if the issue is with the pointing device or the system.
Check if the touchpad ribbon cable is loose
The most common “hardware” reason for a dead cursor is the internal ribbon cable that connects the touchpad to the motherboard. It often shifts when you open the laptop lid or when the chassis flexes. For the detail, see our notes on resolving trackpad calibration.
If the cursor works intermittently only when you press the palm rest firmly, the cable connector is likely loose. The pressure forces the contacts to touch properly until you let go.
- Power off the laptop and unplug the AC adapter.
- Remove the battery if it is user-accessible. If internal, disconnect the battery clip first.
- Open the bottom panel to access the touchpad connector.
- Re-seat the ZIF connector by lifting the latch tab and pushing the cable back in firmly.
After re-seating, close the panel and restart the laptop. If the cursor moves immediately, you have found the issue. If it remains frozen, move to the next step.
Safety first: Always disconnect the internal battery before touching any ribbon cables to prevent shorting the motherboard.
A replacement touchpad module with a bracket ensures a secure fit if the original cable or housing is cracked.
- Compatible with Dell XPS 15 9520 9530 and Precision 15 5570 15.6-inch Laptop Series
- *[NOTE]*: NOT FITS for XPS 17 9700 9710 9720 and Precision 17 5750 5760 5770, XPS 15
Test with an external USB mouse
Before opening the laptop, plug in a standard USB mouse. If the external mouse works perfectly, your motherboard and USB controllers are fine. This step isolates the fault to the touchpad assembly or its specific ribbon cable.
Use a wired mouse to rule out wireless interference. Wireless dongles can fail due to low batteries, driver conflicts, or USB port issues that mimic hardware failure.
If the wired mouse also does not work, the issue is likely a motherboard USB controller failure or a Windows driver crash. In this case, the problem is not specific to the touchpad hardware but to the system input handling. It helps to understand resolving a frozen cursor issue before going further.
Pro tip: If the USB mouse also does not work, the issue is likely a motherboard USB controller failure or a Windows driver crash.
A responsive 1000 dpi wired mouse provides reliable tracking to test the system without wireless variables.
- Computer mouse for easily navigating a computer interface; click, scroll, and more
- A wired connection; if existing device only supports USB-C, an additional adapter will
Verify battery swelling is not pressing the touchpad
A swollen lithium-ion battery can physically push against the touchpad housing from below. This pressure breaks the sensor’s contact points or deforms the flexible circuit.
Look for a bulging bottom panel, a gap between the keyboard and palm rest, or a hinge that does not close flat. These are physical signs of internal pressure.
If you see any swelling, stop using the laptop immediately. Do not attempt to flatten it. A swollen battery must be removed and recycled safely. Continued use poses a fire hazard.
Inspect the touchpad sensor and flex cables
If the cable is seated and the battery is flat, check the touchpad itself. Look for frayed wires where the flex cable bends near the hinge or where it enters the palm rest.
Micro-fractures in the flex trace cause the cursor to jump, disappear, or lag when the hinge moves. This is common in laptops that are frequently transported. We go through swapping out a faulty input device step by step in its own article.
You can sometimes bypass a cracked flex cable by carefully reseating it and adding strain relief with Kapton tape or flexible plastic sleeves. This prevents further wear on the trace.
Differentiate between sensor failure and logic board damage
Touchpads use optical sensors or digitizers. If the device is old, the laser diode or LED array may have burned out due to thermal stress. This results in a total loss of signal.
Check Device Manager for touchpad controller errors. If Windows does not recognize the device at all, the hardware signal is not reaching the motherboard. Look for yellow exclamation marks under Mice and other pointing devices.
Try updating the chipset drivers. Sometimes a “hardware” feel is actually a driver conflict hiding a good sensor. Disable conflicting drivers in Device Manager to test if the sensor responds.
When to replace the touchpad assembly
If the ribbon cable is seated, the battery is fine, and an external mouse works, the touchpad module itself is likely dead. The internal sensor has failed.
You will need to buy a compatible touchpad replacement part. Ensure it matches your exact laptop model number, not just the size. The ribbon cable connector varies by manufacturer. We go through laptop on off switch not connecting to the mother board step by step in its own article.
Installation requires removing the keyboard assembly on some models, which increases the difficulty of the repair. If you are not comfortable with this, take it to a professional repair desk.
The bottom line
Start by plugging in a wired USB mouse to confirm the issue is isolated to the touchpad. If the cable is loose, re-seating the ZIF connector often fixes the problem for free. If the sensor is dead, replace the touchpad module with a part that matches your exact laptop model.
- Computer mouse for easily navigating a computer interface; click, scroll, and more
- A wired connection; if existing device only supports USB-C, an additional adapter will
Frequently asked questions
Why does my cursor only work when I press the palm rest?
This indicates a loose ribbon cable or a swollen battery pushing against the touchpad. The pressure closes the gap in the connection. Re-seating the cable or removing the battery usually solves it.
Can a cracked laptop screen affect the mouse cursor?
No, unless the cracked panel is physically pressing on the touchpad housing or ribbon cable. If the screen is merely cracked but not bulging, the touchpad issue is likely separate.
How do I know if the touchpad sensor is broken?
If an external USB mouse works but the touchpad does not, and the cable is securely connected, the optical sensor inside the touchpad is failed. You will need to replace the touchpad assembly.
Is it safe to keep using a laptop with a dead touchpad?
Yes, as long as you use an external mouse. However, do not ignore a swollen battery, which is a fire hazard. Replace the battery immediately if it is bulging.


